[1]李 霏,钱慧来,申梦清,等.高强韧活塞铝合金在高温时效过程中的组织与性能演变[J].西安工业大学学报,2019,(06):682-687.[doi:10.16185/j.jxatu.edu.cn.2019.06.010 ]
 LI Fei,QIAN Huilai,SHEN Mengqing,et al.Evolution of Microstructure and Properties of Piston Aluminum Alloy with High Strength and Toughness During High Temperature Aging Process[J].Journal of Xi'an Technological University,2019,(06):682-687.[doi:10.16185/j.jxatu.edu.cn.2019.06.010 ]
点击复制

高强韧活塞铝合金在高温时效过程中的组织与性能演变()
分享到:

《西安工业大学学报》[ISSN:1673-9965/CN:61-1458/N]

卷:
期数:
2019年06期
页码:
682-687
栏目:
材料科学与工程
出版日期:
2019-12-25

文章信息/Info

Title:
Evolution of Microstructure and Properties of Piston Aluminum Alloy with High Strength and Toughness During High Temperature Aging Process
文章编号:
1673-9965(2019)06-0682-06
作者:
李 霏钱慧来申梦清王 恒杨 伟
(西安工业大学 材料与化工学院,西安 710021
Author(s):
LI FeiQIAN HuilaiSHEN MengqingWANG HengYANG Wei
(School of Materials and Chemical Engineering,Xi'an Technological University,Xi'an 710021,China)
关键词:
活塞铝合金 时效处理 显微组织 力学性能
Keywords:
piston aluminum alloy aging treatment microstructure mechanical properties
分类号:
TG146.2
DOI:
10.16185/j.jxatu.edu.cn.2019.06.010
文献标志码:
A
摘要:
为了预测新型活塞铝合金在高温工况下的服役寿命,文中以Pandat软件平衡计算相图为基础,采用布氏硬度和拉伸性能测试分析了该合金在150~500 ℃下时效0~100 h后的力学性能变化规律,并利用金相显微镜、扫描电子显微镜和透射电子显微镜观察了其显微组织,研究了显微组织对力学性能的影响机理。研究结果表明:该合金在150~500 ℃时效后的力学性能先下降后上升,350 ℃时力学性能最低,150 ℃时硬度曲线出现强化双峰; 时效温度为250~500 ℃时,析出相θ聚集长大,导致合金的力学性能下降; 当时效温度达到425 ℃后,基体析出大量的粒状富镍相和纳米相,导致力学性能下降幅度变小; 当时效温度达到450 ℃后,α-Al固溶体中脱溶析出细小硅相,并聚集长大,提高了合金硬度。
Abstract:
In order to predict the service life of the new piston aluminum alloy during the high temperature aging process,the paper makes an analysis of the mechanical properties of the alloy after 0~100 h aging at 150~500 ℃ by means of the balance phase diagram calculated with the Pandat software and with Brinell hardness test and tensile test.The microstructure of the alloy was observed by a metallographic optics microscope,a scanning electron microscope and a transmission electron microscope and the effect of the microstructure on its mechanical properties was studied.The results show that the mechanical properties of the alloy reduce first and then rise up after being aged at 150~500 ℃,and are the lowest at 350 ℃.The hardness curve at 150 ℃ shows enhanced double peaks.When the aging temperature is at 250~500 ℃,the precipitated phase θ aggregates and grows up,leading its mechanical properties to decrease.When the aging temperature reaches 425 ℃,a large number of granular nickel-rich phases and nanophases precipitate out of the matrix,resulting in a decrease in its mechanical properties.When the temperature reaches 450 ℃,the fine silicon phase is dissolved and precipitated in the α-Al solid solution,and aggregates and grows,thus increasing the hardness of the alloy.

参考文献/References:


[1] 秦朝举.柴油机活塞铝合金材料烧蚀规律研究[D].北京:北京理工大学,2015. QIN Zhaoju.Investigations on Aluminum Alloy Ablation for Diesel Engine Pistons[D].Beijing:Beijing Institute of Technology,2015.(in Chinese)
[2] 李云国.AlSiCuNiMg系活塞合金高温强化相的研究[D].济南:山东大学,2011. LI Yunguo.The Study of ElevatedTemperature Strengthening Phases of AlSiCuNiMg Piston Alloys[D].Jinan:Shandong University,2011.(in Chinese)
[3] 康福伟,李如一,乔昕,等.热处理工艺对ZL114A铝合金组织及力学性能的影响[J].哈尔滨理工大学学报,2019(1):113. KANG Fuwei,LI Ruyi,QIAO Xin,et al.Effects of Heat Treatment Processing on the Microstructure and Mechanical Properties of ZL114A Aluminum Alloy[J].Journal of Harbin University of Science and Technology,2019(1):113.(in Chinese)
[4] 杨阳.AlSi多元合金中耐热相演变行为与协同强化机制的研究[D].济南:山东大学,2013. YANG Yang.Study on the Evolution and Collaborative Strengthening Mechanism of HeatResistant Phases in Multicomponent AlSi Alloy[D].Jinan:Shandong University,2013.(in Chinese)
[5] 钱钊.高强耐热Al_Si活塞合金的研究[D].济南:山东大学,2009. QIAN Zhao.Study on High Strength HeatResistant AlSi Piston Alloys[D].Jinan:Shandong University,2009.(in Chinese)
[6] 刘文辉,邱群,周凡,等.时效处理对7N01铝合金高温动态力学性能与组织演化的影响[J].稀有金属材料与工程,2018,47(1):311. LIU Wenhui,QIU Qun,ZHOU Fan,et al.Effects of Aging Treatments on the Dynamic Mechanical Properties and Microstructure Evolution of 7N01 Aluminum Alloy at High Temperature[J].Rare Metal Materials and Engineering,2018,47(1):311.(in Chinese)
[7] 强华,徐尊平.热处理对活塞用铝合金微观组织及力学性能的影响[J].热加工工艺,2018,47(2):242. QIANG Hua,XU Zunping.Effect of Heat Treatment on Microstructure and Mechanical Properties of Aluminum Alloy for Piston[J].Hot Working Technology,2018,47(2):242.(in Chinese)
[8] 王春涛,吴树森,潘敏凯,等.Cu含量及时效处理对压铸AlSiCuNiMg合金性能的影响[J].铸造技术,2018,39(3):691. WANG Chuntao,WU Shusen,PAN Minkai,et al.Effect of Cu Content and Aging Treatment on Mechanical Properties of Die Casting AlSiCuNiMg Alloys[J].Foundry Technology,2018,39(3):691.(in Chinese)
[9] 杨伟.新型铸造铝基合金热暴露组织与疲劳性能研究[D].西安:西安工业大学,2012. YANG Wei.Thermal Exposure Microstructures and Fatigue Properties of Novel Aluminum Based Alloys[D].Xi'an:Xi'an Technological University,2012. (in Chinese)
[10] CHEN K Y,KIM D H,YOO Y S,et al.Microstructural Stability of a Single Crystal Superalloy DD8 During Thermal Exposure[J].Journal of Materials Science & Technology,2008(1):127.
[11] LIAUO C S,CHANG H,HUANG J C,et al.Microstructural Evolution and Mechanical Properties of AC8A/Al2O3 Shortfiber Composites After Thermal Exposure at 150 ℃ to 350 ℃ [J].Metallurgical and Materials Transactions A,1995,26(1):143.
[12] 杨伟,李建平,夏峰,等.热暴露对新型铝基活塞合金组织和性能的影响[J].铸造,2012,61(3):312. YANG Wei,LI Jianping,XIA Feng,et al.Effect of Thermal Exposure on the Microstructure and Mechanical Properties of New Type Aluminum Based Piston Alloy[J].Foundry,2012,61(3):312. (in Chinese)
[13] 王爱琴,谢敬佩,王文焱,等.固溶处理对快速凝固过共晶铝硅合金组织性能的影响[J].特种铸造及有色合金,2009,29(3):218. WANG Aiqin,XIE Jingpei,WANG Wenyan,et al.Influence of Solution Treatment on Microstructure and Properties of Rapidly Solidified Hypereutectic AlSi Alloys[J].Special Casting & Nonferrous Alloys,2009,29(3):218.(in Chinese)
[14] 宋新华,陈胜迁,陈立,等.二次固溶对7A04T6铝合金蠕变时效效应的影响[J].金属热处理,2018,43(4):82. SONG Xinhua,CHEN Shengqian,CHEN Li,et al.Effect of Secondary Solution on Creep Aging Behavior of 7A04T6 Aluminum Alloy[J].Heat Treatment of Metals,2018,43(4):82.(in Chinese)
[15] 李润霞,李荣德,吕伟,等.Cu和Mg在铸造AlSiCuMg合金时效过程中的作用[C]//2006中国铸造活动周论文集.沈阳:中国机械工程学会,2006:367. LI Runxia,LI Rongde,LYU Wei,et al.The Effect of Cu and Mg on the Aging Process of AlSiCuMg Cast Alloy[C]//2006 China Foundry Activities Weekly Collection.Shenyang:Chinese Mechanical Engineering Society,2006:367.(in Chinese)

备注/Memo

备注/Memo:
收稿日期:2019-03-06
基金资助:西安工业大学国家级大学生创新创业训练计划项目(201710702040)。 第一作者简介:李 霏(1997-),男,西安工业大学助理研究员。 通信作者简介:杨 伟(1985-),男,西安工业大学助理工程师,主要研究方向为计算材料学及金属基复合材料,E-mail:393993548@qq.com。 (编辑)
更新日期/Last Update: 2019-12-25